Free shipping* (Some exclusions apply)
(805)541-9000 Mon-Fri 6:30am - 5pm PDT

Starite 2Hp Pump parts

Parts for the Hot Spring Starite 2hp Max-E-Glas Jet Pump

The Sta-rite 2Hp Max-E-Glas single speed pump was used on the Hot Spring 1989-1993 Highlife and the 1989-1991 230 volt only Sovereign (IH) model.

Sta-Rite 2Hp Jet Pump Parts Diagram Insert, Seal Plate, Starite-70071 Shaft Seal, Starite-30024 Impeller, Starite 2HP-70120 Diffuser, Starite-30221 Diffuser O-ring, Starite-30222 Diffuser Screw Washer, #8 Ext Tooth, Starite-70158 Diffuser Screw, #8-32 X 7/8in, Starite-70036 Volute Clamp, Starite w/out Nut-30219 Nut, Volute Clamp, Starite-30297 Volute O-Ring, Starite-30220 Compression Fitting, 1-1/2 Drain Nipple, Wavemaster 7000 (ver. 1 & 2) & 9000, Starite-32267 Adapter, 1-1/2in Mipt-31348 Bell Housing Cover-34480 Pump Start Capacitor-Starite 1HP-70128 Pump Run Capacitor, Starite 2HP-70121 Slinger-70039 Points-70129 Bolt, #3/8in-16 X 1in Hex, Starite-70059 Cordset, W/Plug Jet Pump-10409 Rubber Motor Pad-70034 Mounting Bolt Washer-30413 Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite-70035 Diffuser Screw Washer, #8 Ext Tooth, Starite-70158 Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite-70035
Find with Parts Finder Show compatibility chart Hide compatibility chart
This Sta-rite 2HP pump was used on the following spas:
MODEL Serial Range YEAR
Highlife (220v) K-291001 to K-131202 1989-1993
Sovereign (220v) IH-191001 to IH-419999 1989-1991


Barbed Fitting w/ o-ring, Wavemaster & Starite

Hot Spring, Hot Spot & Solana spas only
This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple. The function of this 32267 nipple is to provide a place for the 1/4" vinyl tube to connect onto the suction side of the jet pump which in turn helps drain the jet pumps water when you drain the spa. Also helps prevent and "Air lock" in the Hot Springs baby circulation pumps (Silentflo) plumbing.

Price: $2.94
Bolt, #3/8in-16 X 1in Hex, Starite

Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps. (Ref. #14) on the Starite 1Hp parts page
(Ref. #14) on the Starite 2Hp parts

Price: $1.16
Bolt, 5/16 X 1-1/2in SS Hex Cap, Starite

Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment.

(Ref. #16) on the Starite 1Hp parts page
(Ref. #16) on the Starite 2Hp parts

Price: $1.47
Bolt, Hex Hd 3/8in-16 X 1-3/4in, Starite

Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment.

(Ref. #18) on the Starite 1Hp parts page
(Ref. #18) on the Starite 2Hp parts

Price: $1.16
Compression Fitting O-ring, for 1-1/2" Union

1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps.  This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump.  No teflon tape is needed for the jet pump connections.

Price: $1.47
Diffuser O-Ring, Starite

Diffuser o-ring for the 1hp & 2hp Sta-rite jet pumps used in Hot Spring models prior to 1993.

(Ref. #3) on the Starite 1Hp parts page
(Ref. #3) on the Starite 2Hp parts

Price: $3.15
Diffuser Screw Washer, #8 Ext Tooth, Starite

Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993.

(Ref. #10) on the Starite 1Hp parts page
(Ref. #10) on the Starite 2Hp parts

Price: $1.05
Diffuser Screw, #8-32 X 7/8in, Starite

Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993.

(Ref. #9) on the Starite 1Hp parts page
(Ref. #9) on the Starite 2Hp parts

Price: $4.62
Diffuser, Starite

Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models.

(Ref. #11) on the Starite 1Hp parts page
(Ref. #11) on the Starite 2Hp parts

Price: $48.01
Impeller, 2Hp Starite


Replacement Sta-rite impeller for the 2Hp pumps used on the Hot Spring Highlife prior to 1992.

(Ref. #2) on the Starite 2Hp parts

Price: $86.04
Insert, Seal Plate, Starite

Copper insert (heat sink) used on all 1HP and 2HP Starite Max-E-Glas jet pumps on Hot Spring spas.

(Ref. #25) on the Starite 1Hp parts page
(Ref. #25) on the Starite 2Hp parts

Price: $12.61
Jet Pump Cordset, Hot Spring, 1990-1996

Power cord used on all jet pumps in all Hot Spring spa models from 1990 through the end of 1996. The plug configuration matches the control box receptacle part# 10408.

Price: $11.48
Not Available
Mounting Bolt Washer, Wavemaster

Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment.

(12) on the Wavemaster 4000 parts page
(12) on the Wavemaster 6000 parts page
(11) on the Wavemaster 7000 (ver. 3) parts page
(11) on the Wavemaster 8000 (ver. 2) parts page
(17) on the Starite 1Hp parts page
(17) on the Starite 2Hp parts

Price: $1.16
Nut, Volute Clamp, Starite

Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994.

(Ref. #24) on the Starite 1Hp parts page
(Ref. #24) on the Starite 2Hp parts

Price: $5.04
Pump Mounting Bracket, Starite 2HP

Pump mounting bracket used to secure the 2HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment.
(Ref. #20) on the Starite 2Hp parts

Price: $54.11
Rubber Motor Pad, Wavemaster 7000 (ver. 2)

This pad goes between the motor base and the plastic base buffer against noisy motor vibrations.

Price: $3.26
Run Capacitor, Starite 2HP

Run capacitor used on all 2HP Starite Max-E-Glas jet pumps on Hot Spring spas.

(28) on the Starite 2Hp parts page

List Price: $172.01
Price: $146.21
Seal Plate, Starite

This Sta-rite seal plate is the part of the "wet end" that bolts onto the pump motor. This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993.

Note: Comes with a new shaft seal.

(Ref. #1) on the Starite 1Hp parts page
(Ref. #1) on the Starite 2Hp parts

List Price: $175.82
Price: $149.45
Shaft Seal, Starite

Sta-rite shaft seal used on the 1HP and 2HP jet pumps on Hot Spring spas.

(Ref. #12) on the Starite 1Hp parts page
(Ref. #12) on the Starite 2Hp parts

Price: $22.06
Slinger, Starite
Item #: 70039

Water slinger used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps on Hot Spring spas. The slinger prevents water, that may be leaking from the shaft seal, from dripping back into the windings of the electric motor and corroding that motor.

 

 

(Ref. #13) on the Starite 1Hp parts page
(Ref. #13) on the Starite 2Hp parts

Price: $9.56
Spring Clamp, 1/4"

Used to secure 1/4" vinyl tubing to various components.

Note: Wear eye protection when squeezing these little rascals. Service techs typically use either needle nose pliers or hose clamp pliers to squeeze, then slide this spring clamp onto the vinyl tubing.

Price: $1.05
Starite Compression Fitting, 1-1/2"

1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas. (35) on the Starite 1Hp parts page
(35) on the Starite 2Hp parts

Price: $41.81
Starite Compression Fitting, 1-1/2"

OBSOLETE AS OF 1-2011
1-1/2" compression coupling assembly (pump union) for all 1-1/2" Starite pump volutes. Sta-Rite pumps can be identified by the model number of the pump beginning with PE.
(38) on the Starite 1Hp parts page
(38) on the Starite 2Hp parts

Price: Not available
Not Available
Start Capacitor, Starite 2HP

Start capacitor used on all 2HP Starite Max-E-Glas jet pumps found on pre-1994 Hot Spring spas.

(Ref. #29) on the Starite 2Hp parts

Price: $53.38
Start Switch, Starite

Start switch (points) used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps on Hot Spring spas.

(Ref. #31) on the Starite 1Hp parts page
(Ref. #31) on the Starite 2Hp parts

Price: Not available
Not Available
Vinyl Tubing, Thick Walled, 1/4" Dia. (ID) x 36"

1/4" inside diameter (ID) by 36" long section of specially made thick walled, clear vinyl tubing. This thick walled tubing will stand up to the harsh chlorinated spa environment for years to come. This is the size of tubing that connects from the front of the jet pump to the circulation pump and heater's plumbing in all 1985-2009 Hot Spring spa models. Click on the "More Info" button for details.

3/4" Vinyl Tubing
1/2" Vinyl Tubing
3/8" Vinyl Tubing
1/4" Vinyl Tubing

Price: $3.68
Volute Clamp, Starite w/out Nut

This stainless steel volute clamp is used to bind the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on Hot Spring spa models.

(Ref. #8) on the Starite 1Hp parts page
(Ref. #8) on the Starite 2Hp parts

Price: $111.26
Volute O-Ring, Starite

Volute o-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993.

(Ref. #7) on the Starite 1Hp parts page
(Ref. #7) on the Starite 2Hp parts

Price: $9.98
Volute, Starite
Item #: 30217

This Sta-rite volute is the front part of the "wet end" of the 1HP and 2HP Max-E-Glas jet pumps used on the Hot Spring spa models prior to 1993.

(Ref. #6) on the Starite 1Hp parts page
(Ref. #6) on the Starite 2Hp parts

List Price: $119.27
Price: $101.38