Free shipping* (Some exclusions apply)
(805)541-9000 Mon-Fri 6:30am - 5pm PDT

Wavemaster® 3000 parts

Parts for Watkins Wavemaster 3000 Jet Pump

This WavemasterŪ 3000 one horsepower two speed jet pump was used on the 1993-2002 Hot Spot Round & Hot Spot RE and 1993-2000 Hot Spot2 and Hot Spot SE. The two speed function employs the low speed for automatic filtration and high speed for hydrotherapy. The pump is designed for 115v. operation for the convenience of a Plug 'N Play environment.

Mouse over the number references in the diagram below

Wavemaster 3000 Parts Diagram Pump Duct Hose Pump Shroud (used to exhaust the pump motor's heat out of the equipment compartment) 1HP two speed pump motor for the Wavemaster 3000 Jet Pump Compression Fitting (aka pump union or pump coupling) Compression Fitting O-ring Pump Volute Shaft Seal Kit Impeller Volute O-ring Wear Ring Volute Cover Hex Nut Set of 4-Rubber Motor Mounts (Reduces the vibration of the pump for quieter operation) Compression Fitting (aka pump union or pump coupling) Compression Fitting O-ring
Find with Parts Finder Show compatibility chart Hide compatibility chart
Wavemaster® 3000, 1 HP/ 2-Speed pump used in the following spas:
MODEL Serial # Range YEAR
Round & RE 1993-2002 Z-131001 to Z-4D9999
Hot Spot2 & SE 1993-2000 Y-131001 to Y-4B9999

Technical Specs:
10.3 amp/115 Volts AC, 1 hp in high speed or 3 amp/115 Volt AC in low speed



Barbed Fitting w/ o-ring, Wavemaster & Starite

Hot Spring, Hot Spot & Solana spas only
This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple. The function of this 32267 nipple is to provide a place for the 1/4" vinyl tube to connect onto the suction side of the jet pump which in turn helps drain the jet pumps water when you drain the spa. Also helps prevent and "Air lock" in the Hot Springs baby circulation pumps (Silentflo) plumbing.

Price: $2.94
Compression Fitting O-ring, for 1-1/2" Union

1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps.  This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump.  No teflon tape is needed for the jet pump connections.

Price: $1.47
Compression Fitting, 1-1/2" with O-Ring

This 1-1/2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling. It is found on the suction and/or discharge side of Wavemaster® Jet Pumps.

1-1/2" Compression Fitting click here
2" x 1-1/2" Compression Fitting click here
2" Compression Fitting click here

Price: $9.04
Compression Fitting, 2" with O-Ring

This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling. It is found on the suction side of most Wavemaster® Jet Pumps. Other compression fittings are the # 71038) and # 71037.

Price: $12.71
Drain Assembly, Hot Spot Z '93-'94

This drain assembly is used on the Wavemaster 3000 and has a 1-1/2" union coupling (compression fitting) on each end and a 3/4" male hose fitting for draining the 1993-1994 Hot Spot Round (Z model) spa. This assembly connects onto the jet pump and the Hot Spot Rounds plumbing. For 1995-1996 use the 35046 .

Price: $41.29
Drain Plug, Wavemaster

This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline. Click on the picture or the "More Info" button for details.

Price: $1.68
Exhaust Hose, Wavemaster

This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor. This method of cooling the jet pump insures a longer lifespan of the pumps motor.

Price: $11.24
Impeller, Wavemaster 3000

This Wavemaster 3000 impeller screws onto the electric motor's threaded shaft with regular right hand threads.

**If your pump has vendor number of "3861" or is a PowerRite or Vico Jet pump, WE DO NOT HAVE REPLACEMENT PARTS. If your Jet pump is an LX jet pump (Vendor Code 3536) the complete wet end must be purchased. Please call our techs for further information and help in finding the correct parts. 

Price: $35.51
Power Cord, Wavemaster

OBSOLETE AS OF 11-2012-Use the 72461

42" Replacement power cord with flag connectors for the Watkins Wavemaster 4000 & Wavemaster 3000 (when used on a 1998-2002 Hot Spot)  jet pump on the Solana and Hot Spot brands. The cord has four wires inside which are BLACK, RED, WHITE, GREEN needed for a two speed jet pump.

Price: Not available
Not Available
Power Cord, Wavemaster 3000

1993-1997 Hot Spot spas
40" replacement power cord (cord set) for the Wavemaster 3000 Jet Pump. This cordset has the correct Molex end connector to enable the Wavemaster 3000 Jet Pump to plug into the control box on all 1993-1997 Hot Spot models.

Price: $37.19
Pump Duct Hose, Wavemaster

OBSOLETE-Use the 72344
Black flexible duct hose (looks like dryer vent hose) attaches to the rear of the jet pump shroud to exhaust heat from the pumps motor to outside of the equipment compartment.

Price: Not available
Not Available
Pump Motor, Wavemaster 1hp/2-Speed
Item #: 70456
compatible
Check Country
Compatiblity

OBSOLETE
This 1hp 2-speed motor is the factory replacement for the Wavemaster 3000 & Wavemaster 4000 jet pump.

Price: Not available
Not Available
Pump Shroud, Wavemaster

OBSOLETE-Use 71414
The shroud attaches to the bottom rear of the motor on the Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000. Its function is to exhaust the heat from the motor through a vent duct (not included) to the outside of the equipment compartment. This feature insures longer life on the Wavemaster pump motors.

Price: Not available
Not Available
Pump Shroud, Wavemaster

This part is obsolete at the factory but we have 1 left in-stock.

Replacement manifold (pump shroud) for the Watkins Wavermaster 3000, 5000 (ver. 1),  7000 (ver. 3) and 8000 (ver. 1 & 2) jet pumps that used an Emerson motor. This shroud attaches onto the rear of the motor and its purpose is to divert heated air from the motor through an exhaust hose to the exterior of the spa. Cool running pump motors last longer!

Price: $18.79
Shaft Seal Kit, Wavemaster

GECKO MODEL SHAFT SEAL

The shaft seal kit is used to prevent water leaking from around the rotating pump shaft. This seal kit is used on most of the Wavemaster jet pumps including the Wavemaster 3000, 4000, 5000, 5000 (ver. 2), 6000, 7000 (ver. 3), 8000, 8000 (ver. 2), 8000 (ver. 3), 8200, 9000 (ver. 2), 9000 (ver. 3), and 9200 jet pumps.

Please note:  If your pump has a vendor number of "4081" on it, then use this part. If your pump has a vendor number of "3536" on it, use part number 77363

**If the vendor number is "3861", WE DO NOT HAVE REPLACEMENT PARTS. Please order the complete pump 71699.

Price: $21.12
Volute Cover Screw, 8-32 X 5/8", Wavemaster

GECKO MODEL SCREW

This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps.

Price: $1.47
Volute Cover, Wavemaster

The volute cover is the second half of the "wet end" (front end or suction plate) and attaches to the volute on all Wavemaster 3000, Wavemaster 5000 and Wavemaster 8000 jet pumps.

Price: $33.62
Volute O-ring, Wavemaster

Large o ring that fits in between the two halves of the "wet end" (volute & volute cover) of the Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000 jet pumps.

Price: $2.31
Volute, Wavemaster

This volute is one half of the "wet end". This part attaches to the jet pump motor with four bolts that are accessed from the rear of the Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000 jet pump motors.

Price: $36.46
Wear Ring, Wavemaster

The jet pump wear ring (slinger) keeps water from back flowing around the impeller which would reduce the jet pressure significantly. Click on the "More Info" button for details.

Price: $2.10