load
The cart is empty

Wavemaster® 4000 parts

Parts for Watkins Wavemaster 4000 Jet Pump

This WavemasterŪ 4000 one horsepower two speed jet pump was used on the 1998-2002 Hot Spot RLX and SLX models and the 2000-2002 Solana X, 2003-current Solana TX and RX models.The two speed function employs the low speed for automatic filtration and high speed for hydrotherapy. The pump is designed for 115v. operation for the convenience of a Plug 'N Play environment.

Mouse over the number references in the diagram below

Wavemaster 4000 Exploded Illustration Pump Shroud (used to exhaust hot air away from the pump motor to the outside of the equipment compartment) 1HP two speed pump motor Volute Shaft Seal Impeller Wear Ring Volute O-ring Volute Cover Volute Screw (stainless steel) Rubber Mounts (feet) for the Wavemaster jet pump. Used to buffer the vibrations from the jet motor within the equipment compartment. 1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment Washer
Find with Parts Finder Show compatibility chart Hide compatibility chart
Wavemaster® 4000, 1 HP/ 2-Speed pump used in the following spas:
MODEL Serial # Range YEAR
RLX 1998-2002 ZQ-181001 to ZQ-4D9999
SLX 1998-2002 YQ-181001 to YQ-4D9999
Wavemaster® 4000, 1 HP/ 2-Speed pump
MODEL YEAR Serial # Range
X 2000-2002 X-1B1001 to X-4D9999
TX 2003-current TX-1E1001 to current
RX 2003-current RX-1E1001 to current

Technical Specs:
10.3 amp/115 Volts AC, 1 hp in high speed or 3 amp/115 Volt AC in low speed
Like:37334



Search within products:

Barbed Fitting w/ o-ring, Wavemaster & Starite
Item #: 32267

More Info  

Hot Spring, Hot Spot & Solana spas only
This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple. The function of this 32267 nipple is to provide a place for the 1/4" vinyl tube to connect onto the suction side of the jet pump which in turn helps drain the jet pumps water when you drain the spa. Also helps prevent and "Air lock" in the Hot Springs baby circulation pumps (Silentflo) plumbing.

List Price: $2.40
Price: $2.13

Compression Fitting, 2" with O-Ring
Item #: 71036

More Info  

This 2" compression fitting, which includes the o ring, is sometimes referred to as a pump union or compression coupling. It is found on the suction side of most Wavemaster® Jet Pumps. Other compression fittings are the # 71038) and # 71037.

List Price: $10.60
Price: $9.35

Drain Plug, Wavemaster
Item #: 32267-1

More Info  

This drain plug is screwed into the female port on the front of Wavemaster 3000, Wavemaster 4000 and 6000 jet pumps when there is an absence of a bleedline. Click on the picture or the "More Info" button for details.
List Price: $1.20
Price: $1.11

Exhaust Hose, Wavemaster
Item #: 72344

More Info  

This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor. This method of cooling the jet pump insures a longer lifespan of the pumps motor.
Price: $8.25

Impeller, Wavemaster 4000
Item #: 71695

More Info  

Replacement impeller for the Watkins Wavemaster 4000 jet pump. This impeller screws onto the pump motor's threaded shaft with regular right hand threads. Click on the "More Info" button for details.

List Price: $23.80
Price: $20.91

Mounting Bolt Washer, Wavemaster
Item #: 30413

More Info  

Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment.

(12) on the Wavemaster 4000 parts page
(12) on the Wavemaster 6000 parts page
(11) on the Wavemaster 7000 (ver. 3) parts page
(11) on the Wavemaster 8000 (ver. 2) parts page
(17) on the Starite 1Hp parts page
(17) on the Starite 2Hp parts

Price: $0.77

Mounting Bolt, Wavemaster
Item #: 30018

More Info  

1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment. Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000.3 jet pumps.
List Price: $0.90
Price: $0.85

Power Cord, Wavemaster
Item #: 71698

More Info  

OBSOLETE AS OF 11-2012-Use the 72461

42" Replacement power cord with flag connectors for the Watkins Wavemaster 4000 & Wavemaster 3000 (when used on a 1998-2002 Hot Spot)  jet pump on the Solana and Hot Spot brands. The cord has four wires inside which are BLACK, RED, WHITE, GREEN needed for a two speed jet pump.
Price: This item is not available
Not Available

Pump Motor, Wavemaster 1hp/2-Speed
Item #: 70456
compatible
Check Country
Compatiblity

More Info  

OBSOLETE
This 1hp 2-speed motor is the factory replacement for the Wavemaster 3000 & Wavemaster 4000 jet pump.
Price: This item is not available
Not Available

Pump Shroud, Wavemaster
Item #: 71415

More Info  

OBSOLETE

For Magnetek or AO Smith Century Motors Only

Replacement manifold (pump shroud) for the Watkins Wavemaster 4000, 5000, 5000 (ver.2), 6000, 7000 (ver. 3), 8000 (ver. 3), 8200, 9000 (ver. 3) and 9200 jet pumps. This shroud attaches onto the rear of the Magnetek or AO Smith Century motor. Its purpose is to divert heated air from the motor through an exhaust hose to the exterior of the equipment compartment. Cool running jet pump motors last longer!
Price: This item is not available
Not Available

Pump Shroud, Wavemaster 4000 (Emerson Motor)
Item #: 71697

More Info  

For Emerson Motor Only
Replacement pump shroud for the Watkins Wavemaster 4000 jet pump with an Emerson motor. This shroud attaches onto the rear of the pumps Emerson motor and its purpose is to divert heated air from the motor, through an exhaust hose, to the exterior of the spa. Cool running pump motors last longer!

Note: If you have a Wavemaster with a Magnetek or AO Smith Century motor then you'll need the 71415 pump shroud.
List Price: $18.80
Price: $16.49

Shaft Seal Kit, Wavemaster
Item #: 71447

More Info  

The shaft seal kit is used to prevent water leaking from around the rotating pump shaft. This seal kit is used on most of the Wavemaster jet pumps including the Wavemaster 3000, 4000, 5000, 5000 (ver. 2), 6000, 7000 (ver. 3), 8000, 8000 (ver. 2), 8000 (ver. 3), 8200, 9000 (ver. 2), 9000 (ver. 3), and 9200 jet pumps.

List Price: $17.70
Price: $15.56

Volute Cover Screw, 8-32 X 5/8", Wavemaster
Item #: 71413

More Info  

This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps.
List Price: $1.10
Price: $1.02

Volute Cover, Wavemaster
Item #: 71696

More Info  

The volute suction cover is the second half of the pumps volute. This factory replacement is for the Wavemaster 4000, 6000, 8000 (ver. 3), 8200, 9000 (ver. 3), 9200 jet pumps. Click on the "More Info" button for details.

Price: $39.21

Volute O-Ring, Wavemaster
Item #: 71554

More Info  

Replacement o ring (largest o-ring) for the Wavemaster 4000, 6000, 8000 (ver. 3), 8200, 9000 (ver. 3), 9200 jet pumps.
List Price: $1.80
Price: $1.62

Volute, Wavemaster
Item #: 71693

More Info  

This part connects onto the motor using long four hex bolts that insert through the rear of the pump motor and screw into this volute. Replacement volute for the Wavemaster 4000, 6000, 8000 (ver. 3), 8200, 9000 (ver. 3) and 9200 jet pumps. Clcik on the "More Info" button for details.

Price: $39.85

Wear Ring, Wavemaster
Item #: 71409

More Info  

Wear Ring (slinger) for the Watkins Wavemaster 4000, 5000 (ver. 2), 6000, 7000 (ver. 3), 8000 (ver. 2), 8000 (ver. 3), 8200, 9000 (ver. 3) and 9200 jet pumps.
List Price: $1.80
Price: $1.62