GlideRite® Retractable Cover System Parts

This bearing is placed over the ¼” – 20 x 1” Hex Head Bolt.
Illustration (# 15) on the Gliderite parts page

These bolts are used with washers to fasten the left and right Base Tubes on a Gliderite.
Illustration (# 5) on the Gliderite parts page

(OBSOLETED 2010)
The Gliderite has three black tubular bars (left, center & right) that fit together and form one long bar that mounts near the bottom base of the spa. This tube is the longest and fits in the center between the left side and rightside.
Illustration (# 9) on the Gliderite parts page

(OBSOLETED 2010)
The Gliderite has three black tubular bars (left, center & right) that fit together and form one long bar that mounts near the bottom base of the spa. This tube is for the left hand side only.
Illustration (# 13) on the Gliderite parts page

The Gliderite has three black tubular bars (left, center & right) that fit together and form one long bar that mounts near the bottom base of the spa. This tube is for the right hand side only .
Illustration (# 13b) on the Gliderite parts page

(OBSOLETED 2010)
This left side Corner Tube Assembly comes with the pivot collar and screw.
Illustration (# 10a) on the Gliderite parts page

This right side Corner Tube Assembly comes with the pivot collar and screw.
Illustration (# 10b) on the Gliderite parts page

(OBSOLETED 2010)
This part is also referred to as a Jaw Slide Pivot Collar. It is located at the end of the base tube assembly.
Illustration (# 18) on the Gliderite parts page

(OBSOLETED 2010)
This bracket is attached to the spa side panel and used with the Slide Lock Bar. Illustration (# 1) on the Gliderite parts page

OBSOLETE
The curved side arm is a black 1" x 1" tubular piece that's used on both sides of the Gliderite Cover Lifter and attaches to both sides of the spa cover. It is specifically used on the Hot Spot SE and SLX and on the Solana SX spa models. If your side arm is straight click here.
Illustration (# 12) on the Gliderite parts page

OBSOLETE AS OF 1-2010

The straight side arm is a black 1" x 1" tubular piece that's used on both sides of the Gliderite Cover Lifter and attaches to both sides of the spa cover. It is specifically used on the Hot Spring & Tiger River spa models. If your side arm is curved click here.
Illustration (# 12) on the Gliderite parts page

The Gliderite slide lock bar is used to lock the spa cover in the vertical position in wind prone areas.
Illustration (# 14) on the Gliderite parts page

This slot tube is found on both sides of the Gliderite and connects to the opposite end of the sidearm that is attached to the spa cover. 

Illustration (# 11) on the Gliderite parts page

This bolt is used to fasten the Slide Lock Bar to the Side Arm.
Illustration (# 17) on the Gliderite parts page

These washers are used with the ¼” – 20 x 5/8” Hex Head Bolts & ¼” – 20 x 1” Hex Head Bolt on the Gliderite and also used on the Uprite cover lifter.

OBSOLETE-Available at most hardware stores

1-1/2in. Phillips flat head screw (Ref. #1) that attaches the side hinge base to the spa cover

OBSOLETE
This Phillips Head screw is used on various cover lifter models.

OBSOLETE
This side hinge screws into the vinyl cover and is used on the Gliderite & Cover Cradle cover lifters. This item is used on all vinyl covers that don't have a curve (radius) where this part will mount to. The side arm of the cover lifter attaches to this part. Includes the sidearm screw

(OBSOLETED 2010)
This washer is placed onto the center screw on the Side Hinge Bracket in front of the Slide Lock Bar.
Illustration (# 16) on the Gliderite parts page