Free shipping on orders over $99 (Some exclusions apply)
(805)541-9000 Mon-Fri 6:30am - 5pm PDT

In this post, we will teach you exactly what to do if the power light on your HotSpring Spa’s control panel is flashing. You may need a couple of basic tools for this tutorial depending on your situation.

Troubleshooting Overview

When the power light on the control panel of your spa is flashing, it means the high limit sensor has tripped. On most occasions, this is caused by poor water circulation due to dirty/clogged filters, air-locks, or a bad circulation pump. On less common occasions there can be an issue with the circuit board, control head, LED light, heater, or the high limit sensor.

Tools Needed:

  • Standard Phillips Screwdriver
  • Voltage Meter

SAFETY FIRST: Turn off the main power to the spa before following any of the steps below.

Step 1

Remove the Spa Filters

Access the filter cartridges in the filter compartment. Remove the filter cartridge with the grey cap. If none of your filters have a grey cap, just remove all of the filters. After the main filter has been removed, Power on the spa.

If the power light on the control panel stops flashing, you need to clean or replace your spa filters.

If the power light keeps flashing, move on to step two.

Step 2

Remove any Air-Locks

If you started experiencing the “power light flashing” issue right after draining and refilling your spa, you may have an air-lock in your system. To clear an air-lock our of your system you will need to follow these steps:

  • Turn off power to the spa
  • Remove the main filter in your spa (usually has a grey cap)
  • Remove the filter standpipe
  • Put a garden hose down the plumbing fitting that leads the circulation pump (use a rag to seal around the hose)
  • Turn the water on full blast and let it run for at least 2 minutes
  • Restore power to the spa

You may notice bubbles coming from different areas in the spa. If you do see this it is likely that you had an air-lock.

If this still didn’t do the trick, try this next step.

Step 3

Check the Circulation Pump

First, you will need to open the spa equipment compartment and locate the circulation pump. Next, check to see if the circulation pump is running. You can place your hand on the pump and you should feel a slight vibration. You should also hear a humming sound. If you know your circulation pump is running, move on to step 4.

If your circulation pump is not running, turn off the power to the spa and open the spa’s control box. Once opened, restore power to the spa. You are going to want to check the voltage where the circulation pump plugs into the board:

  • Set your voltage meter to ACv (200)
  • place one probe on the terminal of the white Circ Pump wire plugs in and the other probe on the terminal where the black Circ Pump wire plugs in.

If you are getting a voltage reading around 120v then you will need to replace your Circulation Pump.

If you are not getting the proper voltage (near 110v-120v), you will need to double-check that the “Summer Time” mode is not enabled. If the Summer Time mode is off, you will need to replace the main motherboard.

Step 5

Check Main Motherboard

In this step, we will inspect the LED lights on the motherboard. If the “Control Unplugged” LED is lit, you may have to replace the control head (or on some occasions a bad Spa Light will be the issue). If only the “LIM OK” LED is lit, you will want to move on to the next step.

Step 6

Check the Spa Heater

Locate your spa’s heater. Run your hand along the outlet side of the metal heater tube. If you notice a spot on the metal tube that is extremely hot, you are most likely dealing with a bad heater.

If the heater isn’t too hot to touch, move on to the next step.

Step 7

Check Thermistors

If the issue hasn’t been discovered at this point, it’s time to check the kOhms of your thermistors. For instructions on checking the kOohms on your thermistors, click the link below:

https://www.backyardplus.com/proddetail.php?prod=39205

Final Step

If none of these steps has resolved the Blinking Power light Issue, please give our Spa Technicians a call at 805-541-9000.


Our goal here at Backyard Plus is to help save you money by avoiding costly service calls for repairs that you can easily do yourself!

If you are looking for HotSpring Spa replacement parts or water care products for your spa, we have what you need! backyardplus.com

For more helpful tips and How-To Videos, visit our YouTube channel!

Thanks for reading!

If there are any topics you would like to learn about pertaining to your HotSpring Spa, please let us know.