Free shipping on orders over $99 (Some exclusions apply)
(805)541-9000 Mon-Fri 6:30am - 5pm PDT
We are operating normally and shipping "in stock" items same day.

Heaterbody, Hot Spring, 115V., 1/2" Ports, 1980-1989

Item #: 30786

Heaterbody, Hot Spring, 115V., 1/2" Ports, 1980-1989


What's Included: Heaterbody, 115V -Stainless Steel- 1/2 inch ports

Description: Stainless steel heater housings with 1/2 inch ports were used on all 1980-1989 115v. Hot Spring spa models. The housing (heater body) is tubular in shape and has three intake/discharge ports. The two larger ports (1/2"), located on the end of the housing, are used to circulate water through the housing via the small, low flow circulation pumps. The smaller port (1/4"), also located at the end of the housing, is used to drain the spa heater in preparation of winterization.

Compatible Hot Spring models for this heater housing
Models Serial # Range Years
All 115v models   1980-1989

Check Serial Number Compatibility

Related Items

Heater Element, Hot Spring, 115v 1.5kW, Pre-1995
Item #: 31255
Check Country

GOOD NEWS---Heaters are here!!


What's included: Heater element w/ power cord

NOTE: You must order the O-Ring (31212) and Gasket (70108)

This 1500 watt heater element is the replacement for all 1980-1994 Hot Spring spa models that operated on 115volts. This heater element, located inside of a stainless steel cylinder style housing, is an immersion type heater. If your spa is older than 1989, you will need the cord adapter (30070) or splice in your old cord end onto this new element. Click the "More Info" button for details.  Please note: Warranty is void if the heater has been dry fired.  Refill your spa through the filter compartment to keep air from forming in the manifold.  Please contact our tech support for more installation info.

Restocking Fee Policy:
Price: $199.99
Heater Replacement Kit, Hot Spring, 1/2" Ports-115V., 1980-1989
Item #: 20286.50-BYP
Check Country

Replacement heater kit for all 115 volt Hot Spring spa models manufactured from 1980-1989. This heater has 1/2" inlet and outlet ports found on the Hot Spring Classic, Home Spa, Indoor/Outdoor, Personal Spa, Jetsetter, Prodigy and Sovereign spa models.  Click on the picture or the "More Info" button for details.

Price: $399.99
Insulation, Heaterbody 115V

(Ref. #6) This insulation minimizes the heat loss through the heater housing.  The insulation is wrapped around the stainless steel heater body used in 115 volt spas made from 1980 to 1994.

Price: $28.03
Nut, Hex #10-24in SS

(Ref. #7) Used on the 1980-1994 115volt Hot Spring heaters in conjunction with the stainless steel screw (30348) to secure the heater element to the heater body.

Price: $1.18
O-Ring, Heaterbody 115V 1.5Kw

(Ref. #5) This o-ring is used to seal the heater element (part#31255) into the heater housing(s) (part# 10475 or #30786)

Price: $1.87
Retainer Gasket, Heaterbody 115V

(Ref. #4) The Retainer is used to hold the Heaterbody O-ring( part#31212) into place on Hot Spring models only.

Price: $3.05
Screw, #10-24 X 3/4in SS

(Ref. #1) Stainless steel screw mostly used on the 1980-1994 115volt Hot Spring heaters to secure the heater element to the heater body.  Four of these are used with each heater.

Price: $1.18
Spring Clamp, 1/2" (.645-.828)

1/2" spring clamp for securing 1/2" vinyl tubing to components.

Note: Wear eye protection when squeezing these little rascals. Service techs typically use either needle nose pliers are hose clamp pliers to squeeze then slide this spring clamp onto the vinyl tubing.

Price: $1.41