Free shipping on orders over $99 (Some exclusions apply)
(805)541-9000 Mon-Fri 6:30am - 5pm PDT

Heater, Hot Spot & Solana, 1999-2005

Item #: 71580

Heater, Hot Spot & Solana, 1999-2005
  (Enlarge)  

Description-

What's Included: Heater-Flow Thru style with compression fitting at both ends

Description: This flow-thru style was used on the 1999-2002 Hot Spot RE, RLX (Z & ZQ model-round spa), 1999-2002 Hot Spot SE & SLX (Y & YQ model-square spa) and 2001-2002 Hot Spot W & WQ model (square spa-wood siding). It was also used on the 2000-2002 Solana X model, 2003-2005 Solana TX model (triangle spa), 2003-2005 Solana RX model (round spa) and the 2003-2005 Solana SX model (square spa). This heater is attached to the control and to the spa's plumbing using the attached compression fittings at both ends.

Hot Spot models
Models Serial # Range Years
RE (round) Z-1A1001 to Z-4D9999 1999-2002
RLX (round) ZQ-1A1001 to ZQ-4D9999 1999-2002
SE (square) Y-1A1001 to Y-4D9999 1999-2002
SLX (square) YQ-1A1001 to YQ-4D9999 1999-2002
SLXtra W-1C0001 to W-4D9999 2001-2002
SLXtra WQ-1C0001 to WQ-4D9999 2001-2002
 
Solana
X X-1B1001 to X-4D9999 2000-2002
TX TX-1E1001 to TX-4G9999 2003-2005
RX RX-1E1001 to RX-4G9999 2003-2005
SX SX-1E1001 to SX-4G9999 2003-2005
 


Technical Specs: 115 Volt AC, 1.0 kW, 8 Amps

HEATER REMOVAL INSTRUCTIONS FOR 2000-2005 SOLANA
1. Disconnect power to the spa.
2. Remove the front access panel (equipment compartment door).
3. Drain the spa.
4. Open the drain valve to bleed the water out of the plumbing.
5. Open the control box lid.
6. Disconnect the pressure switch connection wires from the pressure switch and remove the
pressure switch (refer to the pressure switch removal procedure).
7. With two small wrenches of the same size, loosen the nuts that secure the heater connecting
bars. Then disconnect the ground wire attached to the heater.
WARNING: Always use both wrenches to loosen the heater connecting bar. The bottom nut
is fused to the heater terminal to prevent the terminal from being twisted when the top nut is
turned. If only one wrench is used to loosen the connecting bar, the torque applied to the
heating element will be too great, and the heater will be permanently damaged.
8. Unscrew the heater inlet and outlet compression fittings.
Caution: There may still be some residual water in the plumbing.
9. Slip the heater out of the control box, and remove it from the equipment compartment.

RE-INSTALLATION
Reverse the removal procedure to install the heater in the equipment compartment (refer to the
pressure switch installation procedure if necessary).
Note: After you are finished with the installation, switch the jet pump to high speed
and check the heater's compression fittings for leaks.

Check Serial Number Compatibility

Check Country Compatibility

compatible
Check Country
Compatiblity
Price: Not available
Not Available

Related Items

Compression Fitting O-rings, for 2" Union (Qty of 2)

(Quantity of 2 o-rings) O-rings used on the pumps 2" compression fittings ( 71036 ) found on most Hot Spring, Tiger River, Limelight, Hot Spot and Solana spa models. Also used on the replacement "Wet End" pump kits and some heaters.

Price: $2.96


RECENTLY VIEWED