This male adapter screws into a 1-1/2" jet pump volute in order for a 1-1/2" compression coupling (pump union) to screw onto the adapter.

(34) on the Starite 1Hp parts page
(34) on the Starite 2Hp parts

Hot Spring, Hot Spot & Solana spas only
This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple. The function of this 32267 nipple is to provide a place for the 1/4" vinyl tube to connect onto the suction side of the jet pump which in turn helps drain the jet pumps water when you drain the spa. Also helps prevent and "Air lock" in the Hot Springs baby circulation pumps (Silentflo) plumbing.

Stainless steel bolt used to connect the seal plate to the electric motor on both 1HP and 2HP Sta-rite Max-E-Glas jet pumps. (Ref. #14) on the Starite 1Hp parts page
(Ref. #14) on the Starite 2Hp parts

Stainless steel bolt used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps to secure the mounting bracket to the floor in the Hot Spring equipment compartment.

(Ref. #16) on the Starite 1Hp parts page
(Ref. #16) on the Starite 2Hp parts

Stainless steel bolt used to secure the 1HP and 2HP Sta-rite Max-E-Glas jet pump motor to the mounting bracket in the Hot Spring equipment compartment.

(Ref. #18) on the Starite 1Hp parts page
(Ref. #18) on the Starite 2Hp parts

1-1/2" compression coupling (pump union) o ring for some Wavemaster jet pumps and all Starite pumps.  This o-ring should typically be replaced when removing the jet pump for repair and reinstalling the jet pump.  No teflon tape is needed for the jet pump connections.

Diffuser o-ring for the 1hp & 2hp Sta-rite jet pumps used in Hot Spring models prior to 1993.

(Ref. #3) on the Starite 1Hp parts page
(Ref. #3) on the Starite 2Hp parts

Diffuser screw washer used in addition to the diffuser screw that secures the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993.

(Ref. #10) on the Starite 1Hp parts page
(Ref. #10) on the Starite 2Hp parts

Diffuser screws used to secure the diffuser in place on the 1HP and 2HP Sta-ite Max-E-Glas jet pumps used on Hot Spring models prior to 1993.

(Ref. #9) on the Starite 1Hp parts page
(Ref. #9) on the Starite 2Hp parts

Sta-rite Diffuser used on the 1HP and 2HP Max-E-Glas jet pumps on Hot Spring spa models.

(Ref. #11) on the Starite 1Hp parts page
(Ref. #11) on the Starite 2Hp parts

Impeller for the 1hp Sta-rite used in Hot Spring spas prior to 1993.

(Ref. #2) on the Starite 1Hp parts page

Copper insert (heat sink) used on all 1HP and 2HP Starite Max-E-Glas jet pumps on Hot Spring spas.

(Ref. #25) on the Starite 1Hp parts page
(Ref. #25) on the Starite 2Hp parts

Power cord used on all jet pumps in all Hot Spring spa models from 1990 through the end of 1996. The plug configuration matches the control box receptacle part# 10408.

Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment.

(12) on the Wavemaster 4000 parts page
(12) on the Wavemaster 6000 parts page
(11) on the Wavemaster 7000 (ver. 3) parts page
(11) on the Wavemaster 8000 (ver. 2) parts page
(17) on the Starite 1Hp parts page
(17) on the Starite 2Hp parts

Used to tighten the volute clamp that binds the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on some Hot Spring spa models prior to 1994.

(Ref. #24) on the Starite 1Hp parts page
(Ref. #24) on the Starite 2Hp parts

Pump mounting bracket used to secure the 1HP Sta-rite Max-E-Glas jet pump to the floor of the Hot Spring equipment compartment.

(20) on the Starite 1Hp parts page

This pad goes between the motor base and the plastic base buffer against noisy motor vibrations.

Run capacitor used on all 1HP Starite Max-E-Glas jet pumps found on pre-1994 Hot Spring spas.

(Ref. #28) on the Starite 1Hp parts page

This Sta-rite seal plate is the part of the "wet end" that bolts onto the pump motor. This seal plate is the replacement for both the 1hp and 2hp Starite Max-E-Glas jet pumps used on Hot Spring models prior to 1993.

Note: Comes with a new shaft seal.

(Ref. #1) on the Starite 1Hp parts page
(Ref. #1) on the Starite 2Hp parts

Sta-rite shaft seal used on the 1HP and 2HP jet pumps on Hot Spring spas.

(Ref. #12) on the Starite 1Hp parts page
(Ref. #12) on the Starite 2Hp parts

Water slinger used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps on Hot Spring spas. The slinger prevents water, that may be leaking from the shaft seal, from dripping back into the windings of the electric motor and corroding that motor.

(Ref. #13) on the Starite 1Hp parts page
(Ref. #13) on the Starite 2Hp parts

Used to secure 1/4" vinyl tubing to various components.

Note: Wear eye protection when squeezing these little rascals. Service techs typically use either needle nose pliers or hose clamp pliers to squeeze, then slide this spring clamp onto the vinyl tubing.

1-1/2" compression coupling assembly (pump union) for all Starite pumps used on Hot Spring spas. (35) on the Starite 1Hp parts page
(35) on the Starite 2Hp parts

OBSOLETE AS OF 1-2011
1-1/2" compression coupling assembly (pump union) for all 1-1/2" Starite pump volutes. Sta-Rite pumps can be identified by the model number of the pump beginning with PE.
(38) on the Starite 1Hp parts page
(38) on the Starite 2Hp parts

Start capacitor used on all Sta-rite 1Hp Max-E-Glas jet pumps found on pre-1994 Hot Spring Grandee, Classic, Indoor/Outdoor and Sovereign spa models.

(Ref. #28) on the Starite 1Hp parts page

Start switch (points) used on the 1HP and 2HP Sta-rite Max-E-Glas jet pumps on Hot Spring spas.

(Ref. #31) on the Starite 1Hp parts page
(Ref. #31) on the Starite 2Hp parts

1/4" inside diameter (ID) by 36" long section of specially made thick walled, clear vinyl tubing. This thick walled tubing will stand up to the harsh chlorinated spa environment for years to come. This is the size of tubing that connects from the front of the jet pump to the circulation pump and heater's plumbing in all 1985-2009 Hot Spring spa models. Click on the "More Info" button for details.

3/4" Vinyl Tubing
1/2" Vinyl Tubing
3/8" Vinyl Tubing
1/4" Vinyl Tubing

This stainless steel volute clamp is used to bind the volute and seal plate together on all 1HP and 2HP Starite Max-E-Glas jet pumps that were used on Hot Spring spa models.

(Ref. #8) on the Starite 1Hp parts page
(Ref. #8) on the Starite 2Hp parts

Volute o-ring used on the Sta-rite 1HP and 2HP Max-E-Glas jet pump on Hot Spring spa models prior to 1993.

(Ref. #7) on the Starite 1Hp parts page
(Ref. #7) on the Starite 2Hp parts

This Sta-rite volute is the front part of the "wet end" of the 1HP and 2HP Max-E-Glas jet pumps used on the Hot Spring spa models prior to 1993.

(Ref. #6) on the Starite 1Hp parts page
(Ref. #6) on the Starite 2Hp parts