Free shipping on orders over $99 (Some exclusions apply)
(805)541-9000 Mon-Fri 6:30am - 5pm PDT

Wavemaster® 7000 (version 2) parts

Parts for Watkins Wavemaster 7000 Jet Pump

This is the second version of the Wavemaster 7000 one horsepower single speed jet pump. It was used on the 1995-1996 Hot Spring Grandee and Sovereign models and the 1995-1996 Hot Spring 220volt only Sovereign model.

Wavemaster 7000 version two pump diagram Barbed Fitting Volute Difusser O-Ring Difusser mpeller screw only used on the 2HP version mpeller screw gasket only used on the 2HP version Shaft Seal Seal Plate O-Ring Seal Plate Flat Washer Lock Washer Hex Nut Hex Screw Ground Bonding Lug Pan Screw Motor-Not Available Slinger Pump Shroud Impeller Rubber Pad Pump Base Pump Base Rubber Pad Difusser Lock Washer Difusser Screw Only needed on the WM 9000 (ver. 2)
Find with Parts Finder Show compatibility chart Hide compatibility chart
Wavemaster® 7000, 1 HP/ 1-Speed pump used in the following spas:
MODEL YEAR Serial # Range
Grandee 1995-1996 G-251479 to G-469999
Sovereign 1995-1996 I-251816 to I-469999
Sovereign (220v) 1995-1996 IH-251085 to IH-469999

Barbed Fitting w/ o-ring, Wavemaster & Starite

Hot Spring, Hot Spot & Solana spas only
This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple. The function of this 32267 nipple is to provide a place for the 1/4" vinyl tube to connect onto the suction side of the jet pump which in turn helps drain the jet pumps water when you drain the spa. Also helps prevent and "Air lock" in the Hot Springs baby circulation pumps (Silentflo) plumbing.

Price: $3.28
Compression Fitting O-Ring, Wavemaster 7000 (ver. 2)  & 9000

OBSOLETE
Compression fitting o-ring (pump union) for all the Wavemaster 7000 (v.2) & Wavemaster 9000 (v.1) jet pumps. Use the 34447 o-ring .

Price: Not available
Not Available
Diffuser Lock Washer, #8 Ext.Tooth Wavemaster 7000 (ver. 2) & 9000

Lock washer for the diffuser screw on a Wavemaster 7000 (ver. 2) and Wavemaster 9000 jet pump.

Price: $2.57
Diffuser Screw, 8-32 X 7/8" Rd.Hd.,  Wavemaster 7000 (ver. 2) & 9000

This stainless steel screw secures the diffuser to the seal plate on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump.

Illustration # ( 20 ) on the Wavemaster 7000 (ver. 2) Page.
Illustration # ( 20 ) on the Wavemaster 9000 Page.

Price: $2.82
Diffuser, Wavemaster 7000 (ver. 2) & 9000

The diffuser mounts onto the seal plate of the Wavemaster 7000 second version and the Wavemaster 9000 jet pump using seven stainless steel screws.

Illustration # ( 13 ) on the Wavemaster 7000 (ver. 2) Page.
Illustration # ( 13 ) on the Wavemaster 9000 Page.
 

Price: $29.43
Exhaust Hose, Wavemaster

This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor. This method of cooling the jet pump insures a longer lifespan of the pumps motor.

Price: $12.57
Flat Washer, 3/8" Wavemaster 7000 (ver. 2) & 9000

Flat Volute washer for the Wavemaster 7000 version 2 and he Wavemaster 9000.

Price: $2.57
Hex Screw, 3/8-16 X 1" Wavemaster 7000 (ver. 2) & 9000

This hex screw runs through the flange of the motor into the seal plate on a Wavemaster 7000 second version and a Wavemaster 9000 jet pump.  They are used to hold the seal plate in place against the motor.

Illustration # ( 4 ) on the Wavemaster 7000 (ver. 2) Page.
Illustration # ( 4 ) on the Wavemaster 9000 Page.
 

Price: $4.35
Impeller, Wavemaster 7000 (ver. 2)

1 hp pump impeller for the Wavemaster 7000 (version 2) jet pump. This impeller screws onto the pump motor's threaded shaft with regular right hand threads.

Price: $52.51
Jet Pump Cordset, Hot Spring, 1990-1996

Power cord used on all jet pumps in all Hot Spring spa models from 1990 through the end of 1996. The plug configuration matches the control box receptacle part# 10408.

Price: $11.48
Not Available
Nut Hex 3/8"-16 Wavemaster 7000 (ver. 2) & 9000

This nut goes onto the volute bolt that secures the seal place to the volute.

Price: $3.28
O-Ring, Diffuser Wavemaster 7000 (ver. 2) & 9000

(Ref. #14) O-ring that mounts onto the front of the pump diffuser.

Price: $7.15
O-Ring, Seal Plate, Wavemaster 7000 (ver. 2) & 9000

Largest o ring on the Wavemaster 7000 second version and the Wavemaster 9000 jet pump seal plate.

Price: $10.43
Pump Shroud Air Vent, Wavemaster 7000 (ver. 2) & 9000

Pump Shroud Air Vent for Wavemaster 7000 version 2 and Wavemaster 9000.

Price: $42.54
Rubber Motor Pad, Wavemaster 7000 (ver. 2)

This pad goes between the motor base and the plastic base buffer against noisy motor vibrations.

Price: $3.64
Rubber Pad, Wavemaster 7000 (ver. 2)

This rubber pad fits in between the motor and the steel base on the Wavemaster 7000 (version 2) and provides a buffer against vibrations. This is one of two rubber pads that mount on the steel base. The second is under the base between the base and the floor of the equipment compartment.

Price: $3.64
Seal Plate, Wavemaster 7000 (ver. 2) & 9000

Seal Plate for the Wavemaster 7000 version 2 and the Wavemaster 9000.

Price: $119.23
Shaft Seal, Wavemaster 7000 (ver. 2) & 9000

Replacement Shaft Seal for the Wavemaster 7000 version 2 and the Wavemaster 9000.

Instructions

Illustration # ( 10 ) on the Wavemaster 7000 (ver. 2) Page.
Illustration # ( 10 ) on the Wavemaster 9000 Page.

Price: $32.48
Slinger, Wavemaster 7000 (ver. 2) & 9000

This slinger is for the Wavemaster 7000 version 2 and the Wavemaster 9000. If the pumps shaft seal was to begin leaking, the slinger would "sling" water off the shaft to prevent that water from migrating into the electric motor.

Price: $5.03
Steel Base, Wavemaster 7000 (ver. 2)

This black steel base supports the motor of the Wavemaster 7000 v.2 and bolts onto the floor of the Hot Spring equipment compartment.

Illustration # ( 26 ) on the Wavemaster 7000 (ver. 2) Page.

Price: $52.17
Union Riser, Wavemaster 7000 (ver.2)

OBSOLETE AS OF 12-2013
Union riser is located on the suction & discharge of the Wavemaster 7000 version 2. This fitting screws onto the front & top of the pump just hand-tight. The o-ring is included with this riser. The compression fitting (union) screws onto this riser. Click on the "More Info" button for details.

Price: Not available
Not Available
Volute Lock Washer, 3/8" Wavemaster 7000 (ver. 2) & 9000

One of two volute washers on the Wavemaster 7000 (second version) and the Wavemaster 9000 jet pump.

Price: $3.28
Volute, Wavemaster 7000 (ver. 2) & 9000

Volute for the Wavemaster 7000 version 2 and the Wavemaster 9000 v.1.

List Price: $197.97
Price: $168.27