Wavemaster® 7000 (version 3) parts

For Tiger River and Limelight spas only
This 1/2" barbed adapter fitting is located on the front of  Wavemaster Jet Pumps on Tiger River and Limelight spas. Click on the "More Info" button for details.  Teflon tape should be used on the threads of this fitting for installation.

Hot Spring, Hot Spot & Solana spas only
This barbed nipple screws into the front (suction cover) and is used on all Wavemaster Jet Pumps as well as the Sta-Rite 1Hp & 2Hp jet pumps on everything but Tiger River spas which use a 33732 nipple. The function of this 32267 nipple is to provide a place for the 1/4" vinyl tube to connect onto the suction side of the jet pump which in turn helps drain the jet pumps water when you drain the spa. Also helps prevent and "Air lock" in the Hot Springs baby circulation pumps (Silentflo) plumbing.

Wet End Seal Kit for the Wavemaster 7000 (ver.3) Jet Pump. These parts only fit the pumps with a vendor number ending in 4081. All the replacement parts necessary when opening up the "wet end" to cure a leaking pump. Since the impeller typically breaks when removing it to replace the shaft seal, we have included it in this kit. Click the "More Info" button for details.

Please Note: The manufacturer used several vendors for the wet end side of the 36675 (WM 7000 v.3) Jet pump. If your pump does not have a vendor number on it at all, please call us, we may request photographs to help identify which wet end will work with your pump.

OBSOLETE-Use drain fitting 32267 or 32267-1.
Used on the drain fitting on the front of various Wavemaster jet pumps.

This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor. This method of cooling the jet pump insures a longer lifespan of the pumps motor.

This black impeller is the replacement for the Wavemaster 7000 1.65 HP jet pump. If your existing impeller is gray and not black then you'll need to replace the "wet end kit" of the pump. Click the "More Info" button for details.

**If your pump has vendor number of "3861" or is a PowerRite (model number 36675.01) or Vico Jet pump, WE DO NOT HAVE REPLACEMENT PARTS. If your Jet pump is an LX jet pump (Vendor Code 3536) the complete wet end must be purchased. Please call our techs for further information and help in finding the correct parts. 

Please check vendor code on your pump before ordering replacement parts. For an example of where to find your vendor code, click here.

Wavemaster 7000 1.65HP Generic replacement motor for all 1997 forward Wavemaster 7000 jet pumps. This new replacement motor does not have a shroud available.

Stainless steel washer used with the bolts that secure a pump to the pump stand and the pump stand to the floor of the equipment compartment.

(12) on the Wavemaster 4000 parts page
(12) on the Wavemaster 6000 parts page
(11) on the Wavemaster 7000 (ver. 3) parts page
(11) on the Wavemaster 8000 (ver. 2) parts page
(17) on the Starite 1Hp parts page
(17) on the Starite 2Hp parts

1/4-20 X 1-1/4" long mounting bolt that secures the pump to the floor of the equipment compartment. Used on the Wavemaster 4000, Wavemaster 6000 and Wavemaster 7000.3 jet pumps.

OBSOLETE-Use 72461
Replacement power cord, complete with the end connectors. Fits all single speed Wavemaster jet pumps from 1997 forward.

Replacement manifold (pump shroud) for the Watkins Wavermaster 3000, 5000 (ver. 1),  7000 (ver. 3) and 8000 (ver. 1 & 2) jet pumps that used an Emerson motor. This shroud attaches onto the rear of the motor and its purpose is to divert heated air from the motor through an exhaust hose to the exterior of the spa. Cool running pump motors last longer!

OBSOLETE

For Magnetek or AO Smith Century Motors Only
Replacement manifold (pump shroud) for the Watkins Wavemaster 4000, 5000, 5000 (ver.2), 6000, 7000 (ver. 3), 8000 (ver. 3), 8200, 9000 (ver. 3) and 9200 jet pumps. This shroud attaches onto the rear of the Magnetek or AO Smith Century motor. Its purpose is to divert heated air from the motor through an exhaust hose to the exterior of the equipment compartment. Cool running jet pump motors last longer!

Rubber Mounts (feet) for the Wavemaster jet pump. These are used to buffer the vibrations from the jet motor within the equipment compartment.  Comes in a set of four.

GECKO MODEL SHAFT SEAL

The shaft seal kit is used to prevent water leaking from around the rotating pump shaft. This seal kit is used on most of the Wavemaster jet pumps including the Wavemaster 3000, 4000, 5000, 5000 (ver. 2), 6000, 7000 (ver. 3), 8000, 8000 (ver. 2), 8000 (ver. 3), 8200, 9000 (ver. 2), 9000 (ver. 3), and 9200 jet pumps.

Please note:  If your pump has a vendor number of "4081" on it, then use this part. If your pump has a vendor number of "3536" on it, use part number 77363. 

**If the vendor number is "3861", WE DO NOT HAVE REPLACEMENT PARTS. Please order the complete pump 71699.

Please check vendor code on your pump before ordering replacement parts. For an example of where to find your vendor code, click here.

GECKO MODEL SCREW

This stainless steel screw is used to attach the volute cover to the volute on most Wavemaster jet pumps.

GECKO MODEL VOLUTE COVER

The volute suction cover is the second half of the pumps volute. This factory replacement is for the Wavemaster 4000, 6000, 7000 (ver. 3), 8000 (ver. 3), 8200, 9000 (ver. 3), 9200 jet pumps. Click on the "More Info" button for details.

This is the largest O-ring used on the current Wavemaster series of wet ends for Hot Springs, Tiger River, Solana and Hot Spot model spas.  This o-ring fits between the suction cover and the volute of the pump.  This o-ring is only compatible if your pump has 8 phillips head screws that hold the suction cover to the wet end, and the volute has 2" suction and discharge fittings.

GECKO MODEL WEAR RING

Wear Ring (slinger) for the Watkins Wavemaster 4000, 5000 (ver. 2), 6000, 7000 (ver. 3), 8000 (ver. 2), 8000 (ver. 3), 8200, 9000 (ver. 3) and 9200 jet pumps. Please note: This wear ring is for pumps that have a Vendor Number of "4081" printed on the pump motor. Click more info for details. 

Please Note: The manufacturer used several vendors for the wet end side of the 36675 (WM 7000 v.3) Jet pump. If your pump does not have a vendor number on it at all, please call us, we may request photographs to help identify which wet end will work with your pump.

If your pump has vendor of "4081" on it, then this is the correct wet end.  If your pump has vendor number of "3536" on it, then use part number 77711.

This is the complete "wet end" of the jet pump. The jet pump is comprised of two main components: the electric motor and the "wet end". Click the "More Info" button for details.

**If your pump has vendor number of "3861", WE DO NOT HAVE REPLACEMENT PARTS. Please order complete pump 71699.

Please check vendor code on your pump before ordering replacement parts. For an example of where to find your vendor code, click here.

This is the complete "wet end" of the jet pump. The jet pump is comprised of two main components: the electric motor and the "wet end". Click the "More Info" button for details.  Please note: if your pump has vendor number "3536" on it, then this is the correct replacement part. If your pump has vendor number "4081" on it, then use part number 72994.

**If your pump has a vendor number of "3861", WE DO NOT HAVE REPLACEMENT PARTS. Please order the complete pump 71699.

Please check vendor code on your pump before ordering replacement parts. For an example of where to find your vendor code, click here.