Wavemaster® 8000 parts

For Tiger River and Limelight spas only
This 1/2" barbed adapter fitting is located on the front of  Wavemaster Jet Pumps on Tiger River and Limelight spas. Click on the "More Info" button for details.  Teflon tape should be used on the threads of this fitting for installation.

This exhaust hose connects onto the rear of the jet pumps shroud (if equipped) to discharge hot air from the jet pump motor. This method of cooling the jet pump insures a longer lifespan of the pumps motor.

This impeller was used on the first version of the Wavemaster 8000. On the 1994, 1995 & 1996 Tiger River Khyber spa model. This impeller screws onto the pump motor's threaded shaft with regular right hand threads.

Watch Video

**If your pump has vendor number of "3861" or is a PowerRite or Vico Jet pump, WE DO NOT HAVE REPLACEMENT PARTS. If your Jet pump is an LX jet pump (Vendor Code 3536) the complete wet end must be purchased. Please call our techs for further information and help in finding the correct parts. 

14/3 X 48" power cord with the correct connector for the 1992-1994 Tiger River Khyber, Manora and Tondi spa models.

Power cord with connector used on the Wavemaster 8000 on the 1994-1996 Tiger River Khyber spa model.

OBSOLETE-Use the 72344
Black flexible duct hose (looks like dryer vent hose) attaches to the rear of the jet pump shroud to exhaust heat from the pumps motor to outside of the equipment compartment.

OBSOLETE-Use 71414
The shroud attaches to the bottom rear of the motor on the Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000. Its function is to exhaust the heat from the motor through a vent duct (not included) to the outside of the equipment compartment. This feature insures longer life on the Wavemaster pump motors.

Replacement manifold (pump shroud) for the Watkins Wavermaster 3000, 5000 (ver. 1),  7000 (ver. 3) and 8000 (ver. 1 & 2) jet pumps that used an Emerson motor. This shroud attaches onto the rear of the motor and its purpose is to divert heated air from the motor through an exhaust hose to the exterior of the spa. Cool running pump motors last longer!

GECKO MODEL SHAFT SEAL

The shaft seal kit is used to prevent water leaking from around the rotating pump shaft. This seal kit is used on most of the Wavemaster jet pumps including the Wavemaster 3000, 4000, 5000, 5000 (ver. 2), 6000, 7000 (ver. 3), 8000, 8000 (ver. 2), 8000 (ver. 3), 8200, 9000 (ver. 2), 9000 (ver. 3), and 9200 jet pumps.

Please note:  If your pump has a vendor number of "4081" on it, then use this part. If your pump has a vendor number of "3536" on it, use part number 77363. 

**If the vendor number is "3861", WE DO NOT HAVE REPLACEMENT PARTS. Please order the complete pump 71699.

The volute cover is the second half of the "wet end" (front end or suction plate) and attaches to the volute on all Wavemaster 3000, Wavemaster 5000 and Wavemaster 8000 jet pumps.

Large o ring that fits in between the two halves of the "wet end" (volute & volute cover) of the Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000 jet pumps.

This volute is one half of the "wet end". This part attaches to the jet pump motor with four bolts that are accessed from the rear of the Wavemaster 3000, Wavemaster 5000 & Wavemaster 8000 jet pump motors.

The jet pump wear ring (slinger) keeps water from back flowing around the impeller which would reduce the jet pressure significantly. Click on the "More Info" button for details.